COMEC INKPRINT EAZY90 Series

Brand, size and fixed care information can be printed directly inside a T-shirt neckline instead of on a sewn-in label. In pad printing, the artwork is prepared on a printing plate and a silicone pad transfers suitable ink onto the fabric. Distance from seams, fabric absorbency and drying conditions are determined together.

Inside-neck information can be printed when the same basic T-shirt is produced for different brands and sizes. Line detail, plate and ink transfer are adjusted together for small-text legibility. Changes in fabric weight or finish require verification of earlier settings on a new sample.

Brand, size and fixed product information can be pad printed inside a suitable waistband area on boxer shorts. The fixture must hold the print area flat, preventing elastic and seams from disturbing pad contact. Stretch during wear and washing conditions guide ink and drying selection.

Printing size, fibre content or branding inside briefs can reduce the need for a separate label. Artwork size and pad contact are important in narrow areas. Print feel, stretch behaviour and intended wash performance are assessed on the actual garment where the print touches skin.

Logos and size information can be pad printed onto a flat area inside a vest neckline. Movement in cotton or blended knit fabrics affects definition. A support that holds the garment without excessive tension and an appropriate ink help achieve consistent transfer of small text.

Garment shape and print position are considered together when printing brand, size and care information directly onto underwear. Boxer shorts, vests and briefs may differ in fabric and stretch. Each product therefore requires sample printing to determine its fixture, ink formulation and drying arrangement.

Brand, size and fixed identification markings can be pad printed onto sock soles or suitable knitted areas. A positioning fixture supports consistent placement. Because the surface stretches and experiences friction, both initial appearance and results after washing are checked.

Direct printing can be considered for fixed size, brand or small symbols on sports socks. Raised knit, sole support and tension affect contact. Ink flexibility and abrasion resistance are tested together, and the sample is approved before production.

Size and care information can be printed inside a suitable waistband area on leggings. Ink selection considers flexibility as well as adhesion on elastane blends. The print is examined under intended stretch and washing conditions for cracking or lifting.

Small brand markings and fixed identification information on sportswear can be assessed for pad printing. Polyester ratio, elastane content and exposure to perspiration or friction affect process selection. Artwork size and colour count are planned with the machine configuration and fixture.

Inside-neck size information and small fixed logos can be pad printed on suitable team-shirt fabrics. On polyester, both adhesion and the fabric colour’s effect on the print are assessed. Large graphics and small information markings need different areas, so capacity is selected using actual artwork.

Size and brand information can be printed directly inside the neck or another suitable inner area of baby clothing. Legibility and print feel are assessed together on soft fabrics. Current technical and conformity documents for the ink are reviewed against contact conditions and the customer’s specification when defining the process.

Fixed branding and symbols on underwear waistbands or textile elastic tapes can be assessed for pad printing. Fibre and coating structure and expected stretch determine the result. Prints are compared under tension and at rest, with adhesion and wash resistance checked on actual samples.

When the same garment is produced for different brands, fixed logos and size artwork can be managed with separate printing plates. Records of plates, colours and print positions simplify brand changes. Serial numbers or barcodes that change with every impression require a different solution from pad printing with a fixed plate.

For the EAZY90 group, one-colour information markings and two-colour branding are assessed separately. Cup diameter and maximum print area vary by sub-model. Compare the actual artwork dimensions and colour count with the specification table.

Production planning with EAZY90 considers loading, ink transfer and drying time alongside nominal machine speed. Consistent positioning supports repeated logos and size markings. Plate changes and settings for different sizes or brands are managed through recorded production formulations.

Size, brand and fixed care information can be printed inside a suitable neckline or waistband on pyjamas and loungewear. A flat support prevents fabric bunching. Softness requirements, small-text legibility and intended washing conditions are assessed together.

Size and brand information can be pad printed onto a suitable inner area of thermal underwear. Fabric stretch and surface structure affect adhesion and print feel. Samples are prepared for the intended use and washing conditions; drying settings also consider the fabric’s response to heat.

Small logos, symbols or short fixed text can be considered for woven tapes. Tape width, raised weave and support beneath the print determine definition. Positioning the tape in a fixture maintains alignment during repeated printing; ink is selected using the actual surface.

Print positions for fixed logos and product markings on fabric before cutting are planned with the cutting layout. Machine loading and surface support are assessed for the application. Ink transfer and drying are arranged to suit the next production operation.

Fixed brand, size or orientation markings can be printed onto cut fabric pieces before sewing. A cut edge or defined reference is used for positioning in the fixture. A production sample confirms that the print will not overlap subsequent seams or folds.

Fixed product codes, symbols and identification marks can be printed directly onto technical fabrics. Coatings and service conditions such as temperature and friction guide ink selection. Samples are assessed for initial adhesion and durability appropriate to intended use.

Fixed washing, drying and other care symbols can be pad printed onto suitable textile areas. Line thickness and spacing must remain legible at the selected size. Content follows the manufacturer’s approved product information, and the sample is checked before plate preparation.

Fixed fibre composition and short product information can be printed inside a suitably sized neckline or garment area. Line count and text size are planned with the fabric texture. Plates and production records are organised by product to prevent mixing up text for different fabric blends.

Fixed origin information can be included on the printing plate with a logo and size. Text must follow the approved product information. Rather than squeezing all content into a small area, a sample is prepared considering legible text size and placement together.

Fixed sizes such as S, M, L and XL can be managed with separate printing plates or a planned production arrangement. Garment size and printed information are checked at changeover. Fixed-plate printing differs from automatically changing serial numbers or barcode data.

The ink’s specified drying and waiting time must be completed before assessing wash resistance. Temperature, detergent, drying method and cycle count are defined in advance. The original sample is compared with the washed print to assess adhesion, colour and preservation of fine detail.

Drying and any curing conditions follow the ink series’ technical data sheet. Fabric heat response and available production time are considered together. A touch-dry print may not have reached its final resistance, so the required waiting time is also included in the process.

Line thickness, letter spacing and fabric texture are assessed together for small size and care text. Plate quality, pad contact and ink consistency affect fine-detail transfer. Artwork is considered ready for production only after a sample at the actual print size has been checked for legibility.

The actual fabric, print area and approved artwork are brought together for a trial. Appearance, text legibility, feel and required resistance are assessed on the same sample. Recording the approved ink, plate, pad and drying settings supports repeat production.